RSRP and RSRQ

-

In cellular networks, when a mobile moves from cell to cell and performs cell selection/reselection and handover, it has to measure the signal strength/quality of the neighbor cells. In LTE network, a UE measures two parameters on reference signal: RSRP (Reference Signal Received Power) and RSRQ (Reference Signal Received Quality).

RSRP is a RSSI type of measurement. It measures the average received power over the resource elements that carry cell-specific reference signals within certain frequency bandwidth. RSRP is applicable in both RRC_idle and RRC_connected modes, while RSRQ is only applicable in RRC_connected mode. In the procedure of cell selection and cell reselection in idle mode, RSRP is used.

RSRQ is a C/I type of measurement and it indicates the quality of the received reference signal. It is defined as (N*RSRP)/(E-UTRA Carrier RSSI), where N makes sure the nominator and denominator are measured over the same frequency bandwidth;

The carrier RSSI (Receive Strength Signal Indicator) measures the average total received power observed only in OFDM symbols containing reference symbols for antenna port 0 (i.e., OFDM symbol 0 & 4 in a slot) in the measurement bandwidth over N resource blocks. The total received power of the carrier RSSI includes the power from co-channel serving & non-serving cells, adjacent channel interference, thermal noise, etc.

The RSRQ measurement provides additional information when RSRP is not sufficient to make a reliable handover or cell reselection decision. In the procedure of handover, the LTE specification provides the flexibility of using RSRP, RSRQ, or both. 

Comments

Post a Comment

Popular posts from this blog

SCFT - Single Cell Function test

-
Single Cell Function test SCFT is for verifying whether individual BTS works well or not, by making a single cell function test of BTS hardware and software. Essential items to be tested are as follows: 1) BTS Transmitter Output Measurement Test 2) Initial parameter establishment (Pilot PN/System ID/Site ID/Frequency, Neighbor List) 3) Call Origination and Termination Test 4) Softer Handoff Test/Antenna installation check (Direction, Tilt, Transmission Line) 5) Single Cell Coverage Test 6) Noise Floor Test 7) Parameter check.
Read more

Troubleshooting for GSM KPIs (SD Block & SD Drop)

-
KPIs to be monitored: ·             SD Blocking ·             SD Drop SDCCH Channel: ·    SDCCH channel is a dedicated channel which is using for LAC updation, Call Setup, SMS in Ideal mode. It works in UL & DL SD Blocking: ·    SD Blocking means that you are not getting SD resource for the call origination. When MS connects with Network then RACH and AGCH are provided. After AGCH, SDCCH is provided but if SDCCH is not provided at this time due to some problem or due to unavailable of SD by BSC. KPI Formula in Ericsson: ·             SDCCH CONGESTION = (CCONGS / CCALLS) * 100 ·             CCONGS - Congestion counter. ·  ...
Read more

PS core network

-
Image
The PS core network consists of two parts, the traditional General Packet Radio Service (GPRS) core network and the new Evolved Packet System (EPS) core network. The PS core network connects mobile subscribers to Packet Data Networks (PDNs) such as the Internet, corporate networks or operator services networks.  a functional overview of the PS core network. Logical entities and interfaces are shown in black and form a 2G/3G network, while the blue boxes and lines in Figure  show the LTE/EPC related parts. The LTE/EPC network can be regarded as an extension and evolution of existing 2G/3G networks. From a node implementation perspective, there is no strict border between the two networks. The corresponding logical entities of GPRS and EPS networks can be deployed concurrently in Ericsson PS core nodes, such as the SGSN-MME and EPG; these are marked in red. In addition, Ericsson GPRS nodes can be upgraded with EPC functionality by software only. Network evolution i...
Read more