Huawei Handover Advance Parameter

-

Parameter ID Parameter Name Recommended Value
SYSFLOWLEV System Flux Threshold for Load HO 10
TRIGTHRES Load HO Threshold 90
LoadAccThres Load handover Load Accept Threshold 80
LOADOFFSET Load HO Bandwidth If "Current HO Control Algorithm" in "SET GCELLHOBASIC" is set to HOALGORITHM1, the recommended value of this parameter is 25. If "Current HO Control Algorithm" in "SET GCELLHOBASIC" is set to HOALGORITHM2, the recommended value of this parameter is 8.
LOADHOPERIOD Load HO Step Period If "Current HO Control Algorithm" in "SET GCELLHOBASIC" is set to HOALGORITHM1, the recommended value of this parameter is 10. If "Current HO Control Algorithm" in "SET GCELLHOBASIC" is set to HOALGORITHM2, the recommended value of this parameter is 5.
LOADHOSTEP Load HO Step Level If "Current HO Control Algorithm" in "SET GCELLHOBASIC" is set to HOALGORITHM1, the recommended value of this parameter is 5. If "Current HO Control Algorithm" in "SET GCELLHOBASIC" is set to HOALGORITHM2, the recommended value of this parameter is 2.
QCKSTATCNT MS Fast-moving Watch Cells 3
QCKTRUECNT MS Fast-moving Valid Cells 2
QCKTIMETH MS Fast-moving Time Threshold 15
MAXCNTNUM MAX Consecutive HO Times 3
BANTIME Forbidden time after MAX Times 20
CONTINTV Interval for Consecutive HO Jud. 6
SPEEDPUNISH Penalty on MS Fast Moving HO 30
SPEEDPUNISHT Penalty Time on Fast Moving HO 40
KBIAS K Bias 0
TIGHTBCCHRXQUALTHRES RX_QUAL Threshold for TIGHT BCCH HO 3
TIGHTBCCHHOLOADTHRES Load Threshold for TIGHT BCCH HO 80
MAXRESEND Max Resend Times of Phy.Info. 30
T3105 T3105 7
OutBscLoadHoEn Inter BSC Load Information Allowed NO
SDCCHWaitMREn Waiting for MR on SDCCH Switch OFF
SDCCHWaitMRTimeLen Duration for Waiting MR on SDCCH 10
AssignBetterCellEn Assigning Better Cell Allowed OFF
ABCWaitMaxTime Maximum Better Cell Assigning Duration 40
ABCUpQuality Uplink Quality Threshold in Assigning Better Cell 50
ABCDownQuality Downlink Quality Threshold in Assigning Better Cell 50
LOADHOAD Enhanced Load HO Allowed NO
LAYHOLOADTH Inter-Layer HO Load Threshold 0
LOADHOUSRRATIO HO Ratio of Enhanced Load HO Algorithm 3

Popular posts from this blog

SCFT - Single Cell Function test

-
Single Cell Function test SCFT is for verifying whether individual BTS works well or not, by making a single cell function test of BTS hardware and software. Essential items to be tested are as follows: 1) BTS Transmitter Output Measurement Test 2) Initial parameter establishment (Pilot PN/System ID/Site ID/Frequency, Neighbor List) 3) Call Origination and Termination Test 4) Softer Handoff Test/Antenna installation check (Direction, Tilt, Transmission Line) 5) Single Cell Coverage Test 6) Noise Floor Test 7) Parameter check.
Read more

Troubleshooting for GSM KPIs (SD Block & SD Drop)

-
KPIs to be monitored: ·             SD Blocking ·             SD Drop SDCCH Channel: ·    SDCCH channel is a dedicated channel which is using for LAC updation, Call Setup, SMS in Ideal mode. It works in UL & DL SD Blocking: ·    SD Blocking means that you are not getting SD resource for the call origination. When MS connects with Network then RACH and AGCH are provided. After AGCH, SDCCH is provided but if SDCCH is not provided at this time due to some problem or due to unavailable of SD by BSC. KPI Formula in Ericsson: ·             SDCCH CONGESTION = (CCONGS / CCALLS) * 100 ·             CCONGS - Congestion counter. ·  ...
Read more

PS core network

-
Image
The PS core network consists of two parts, the traditional General Packet Radio Service (GPRS) core network and the new Evolved Packet System (EPS) core network. The PS core network connects mobile subscribers to Packet Data Networks (PDNs) such as the Internet, corporate networks or operator services networks.  a functional overview of the PS core network. Logical entities and interfaces are shown in black and form a 2G/3G network, while the blue boxes and lines in Figure  show the LTE/EPC related parts. The LTE/EPC network can be regarded as an extension and evolution of existing 2G/3G networks. From a node implementation perspective, there is no strict border between the two networks. The corresponding logical entities of GPRS and EPS networks can be deployed concurrently in Ericsson PS core nodes, such as the SGSN-MME and EPG; these are marked in red. In addition, Ericsson GPRS nodes can be upgraded with EPC functionality by software only. Network evolution i...
Read more