LTE parameters for IRAT cell reselection in WCDMA

-

arfcnValueUtranDl   : Indicates the ARFCN applicable for a downlink UTRA carrier frequency, 

cellReselectionPriority  : The absolute priority of the carrier frequency used by the cell reselection procedure. Default Value :7

ellReselectionPriority : The absolute priority of the concerned carrier frequency, as used by the cell reselection procedure. Default Value :6

pMaxUtra : The maximum allowed transmission power on the (uplink) carrier frequency. Default Value :33

sNonIntraSearch :Threshold for inter-frequency and inter-RAT measurements on frequencies of equal or lower priority. Default Value :0

threshServingLow Threshold for the signal strength of the serving cell, below which the UE performs cell reselection towards a lower priority inter-frequency or inter-RAT frequency. Default Value :0

threshXHigh : Specifies the threshold used by the UE when reselecting towards the higher priority frequency X than current serving frequency. Each frequency of UTRAN might have a specific threshold Default Value :4

threshXLow : Specifies the threshold used in reselection towards frequency X priority from a higher priority frequency. Each frequency of UTRAN might have a specific threshold. Default Value :0 

tReselectionUtra : Cell reselection timer value TreselectionRAT for UTRAN (1). Default Value :2

qQualMin : Minimum required quality level in the cell expressed in dB. Default Value :-119


qRxLevMin : Minimum required RX level in the cell expressed in dBm.

Comments

Post a Comment

Popular posts from this blog

SCFT - Single Cell Function test

-
Single Cell Function test SCFT is for verifying whether individual BTS works well or not, by making a single cell function test of BTS hardware and software. Essential items to be tested are as follows: 1) BTS Transmitter Output Measurement Test 2) Initial parameter establishment (Pilot PN/System ID/Site ID/Frequency, Neighbor List) 3) Call Origination and Termination Test 4) Softer Handoff Test/Antenna installation check (Direction, Tilt, Transmission Line) 5) Single Cell Coverage Test 6) Noise Floor Test 7) Parameter check.
Read more

Troubleshooting for GSM KPIs (SD Block & SD Drop)

-
KPIs to be monitored: ·             SD Blocking ·             SD Drop SDCCH Channel: ·    SDCCH channel is a dedicated channel which is using for LAC updation, Call Setup, SMS in Ideal mode. It works in UL & DL SD Blocking: ·    SD Blocking means that you are not getting SD resource for the call origination. When MS connects with Network then RACH and AGCH are provided. After AGCH, SDCCH is provided but if SDCCH is not provided at this time due to some problem or due to unavailable of SD by BSC. KPI Formula in Ericsson: ·             SDCCH CONGESTION = (CCONGS / CCALLS) * 100 ·             CCONGS - Congestion counter. ·  ...
Read more

PS core network

-
Image
The PS core network consists of two parts, the traditional General Packet Radio Service (GPRS) core network and the new Evolved Packet System (EPS) core network. The PS core network connects mobile subscribers to Packet Data Networks (PDNs) such as the Internet, corporate networks or operator services networks.  a functional overview of the PS core network. Logical entities and interfaces are shown in black and form a 2G/3G network, while the blue boxes and lines in Figure  show the LTE/EPC related parts. The LTE/EPC network can be regarded as an extension and evolution of existing 2G/3G networks. From a node implementation perspective, there is no strict border between the two networks. The corresponding logical entities of GPRS and EPS networks can be deployed concurrently in Ericsson PS core nodes, such as the SGSN-MME and EPG; these are marked in red. In addition, Ericsson GPRS nodes can be upgraded with EPC functionality by software only. Network evolution i...
Read more