LTE Paging Parameter

-
Parameter Name
Parameter Description
Default Value
PagingId
The value component of the RDN.

maxNoOfPagingRecords
The maximum allowed number of paging records included in one Radio Resource Control (RRC) paging message. It is the allowed maximum number of UE that can be paged per paging occasion.
3
defaultPagingCycle
The paging cycle (also referred to as T) used by the RBS and broadcast in system information type 2. If the UE-specific Discontinuous Reception (DRX) cycle is provided in S1AP paging and has a smaller value than defaultPagingCycle, the UE-specific DRX cycle overrides defaultPagingCycle.
128
nB
Used to calculate the number and position of Paging Occasions (PO) and Paging Frames (PF).
The numerical value of nB depends on the value of the defaultPagingCycle (T) and can be set to one of the following values:
4T, 2T, T, 1/2T,1/4T, 1/8T, 1/16T, 1/32T
When nB is set to T, 2T or 4T, it determines the number of POs per PF, and the PO position in PF.
When nB is set to a value smaller than T, it affects the System Frame Number of the PF, the position of PO in the PF, and also distribution of UE into groups with the same PF.
When nB is set to a  smaller value, the groups are fewer but larger, or more but smaller.
T
pagingDiscardTimer
The length of time a received paging is retained or queued in the RBS before it is discarded. The timer should be set to the same (or smaller) value as the paging resend timer in MME (T3413). This setting  prevents the RBS from retaining or sending an old paging after the re-sent copy is received from the MME.
3

Popular posts from this blog

SCFT - Single Cell Function test

-
Single Cell Function test SCFT is for verifying whether individual BTS works well or not, by making a single cell function test of BTS hardware and software. Essential items to be tested are as follows: 1) BTS Transmitter Output Measurement Test 2) Initial parameter establishment (Pilot PN/System ID/Site ID/Frequency, Neighbor List) 3) Call Origination and Termination Test 4) Softer Handoff Test/Antenna installation check (Direction, Tilt, Transmission Line) 5) Single Cell Coverage Test 6) Noise Floor Test 7) Parameter check.
Read more

Troubleshooting for GSM KPIs (SD Block & SD Drop)

-
KPIs to be monitored: ·             SD Blocking ·             SD Drop SDCCH Channel: ·    SDCCH channel is a dedicated channel which is using for LAC updation, Call Setup, SMS in Ideal mode. It works in UL & DL SD Blocking: ·    SD Blocking means that you are not getting SD resource for the call origination. When MS connects with Network then RACH and AGCH are provided. After AGCH, SDCCH is provided but if SDCCH is not provided at this time due to some problem or due to unavailable of SD by BSC. KPI Formula in Ericsson: ·             SDCCH CONGESTION = (CCONGS / CCALLS) * 100 ·             CCONGS - Congestion counter. ·  ...
Read more

PS core network

-
Image
The PS core network consists of two parts, the traditional General Packet Radio Service (GPRS) core network and the new Evolved Packet System (EPS) core network. The PS core network connects mobile subscribers to Packet Data Networks (PDNs) such as the Internet, corporate networks or operator services networks.  a functional overview of the PS core network. Logical entities and interfaces are shown in black and form a 2G/3G network, while the blue boxes and lines in Figure  show the LTE/EPC related parts. The LTE/EPC network can be regarded as an extension and evolution of existing 2G/3G networks. From a node implementation perspective, there is no strict border between the two networks. The corresponding logical entities of GPRS and EPS networks can be deployed concurrently in Ericsson PS core nodes, such as the SGSN-MME and EPG; these are marked in red. In addition, Ericsson GPRS nodes can be upgraded with EPC functionality by software only. Network evolution i...
Read more