WCDMA - Idle Mode Parameter

Idle Mode Parameter:

qQualMin:

Minimum required quality level in the cell measured in the UE.

qRxLevMin:

Parameter that indicates the min. required signal strength in the cell

qualMeasQuantity:

Used for decision as to whether the 3G ranking for cell selection and reselection is based on Ec/No or RSCP. Default is Ec/No.

qHyst1:

Hysteresis values used for serving cell, when ranking is based on CPICH RSCP

qHyst2:

Hysteresis values used for serving cell, when ranking is based on CPICHEc/No

qOffset1sn:

Signal strength offset b/w source and target cell for cell ranking based on CPICH RSCP.

qOffset2sn:

Signal offset between serving cell and neighbor cell, based on CPICHEc/No.

sIntraSearch:

Decision on when intra-freq. measurements should be performed. Following criteria is used:

sIntraSearch ≥ qQualmeas - qQualMin (where qQualmeas is the value measured by UE )

sInterSearch:

Parameter is used to make decision to start inter-freq. measurements.

sInterSearch ≥ qQualmeas - qQualMin (where qQualmeas is the value measured by UE )

sRatSearch:

Decision on when GSM measurement should be performed in relation to qQualMin.

sRatSearch ≥ qQualMeas – qQualMin (where qQualmeas is the value measured by UE )

sHcsRatSearch:

Decision on when GSM measurement should be performed in relation to qRxLevMin.

sHcsRatSearch ≥ qRxLevMeas – qRxLevMin (where qRxLevMeas is the value measured by UE)

RRC operation modes?

What are the RRC operation modes?

There are two types of Mode 

1. Idle mode 

2. Connected mode.

There are 4 RRC States: Cell_DCH, Cell_FACH, URA_PCH and Cell_PCH.

Idle Mode: In idle mode, after the UE is switch ON and UE is able to receive system information message from cell.

CELL_DCH: In this state dedicated physical channel is allocated to the UE in UL and DL active set level

CELL_FACH: No dedicated channel is allocated to UE, But RACH and FACH cannel can be used, both transferring signaling message and small amount of data. And in this state UE perform cell re-selection and after a reselection always send a cell update message to RNC

CELL_PCH: In this state UE perform to monitoring of paging information

URA_PCH: It is similar to CELL_PCH expected that the UE does not execute cell update after each re-selection, but instead read URA (UTRA registration area) identities from the broadcast channel.

Cell Search procedure in WCDMA

Cell Search procedure:

During the cell search, the mobile station searches for a cell and determines the downlink scrambling code and common channel frame synchronization of that cell. The cell search is typically carried out in three steps: slot synchronization; frame synchronization and code-group identification; and scrambling-code identification.

Step 1: Slot synchronization.

During the first step of the cell search procedure, the mobile station uses the SCH’s primary synchronization code to acquire slot synchronization to a cell. This can be done with a single matched filter matched to the primary synchronization code that is common to all cells.

Step 2: Frame synchronization and code-group identification.

During the second step of the cell search procedure, the mobile station uses the SCH’s secondary synchronization code to find frame synchronization and identify the code group of the cell found in the first step. This is done by correlating the received signal with all possible secondary synchronization code sequences and identifying the maximum correlation value. Because the cyclic shifts of the sequences are unique, the code group and the frame synchronization are determined.

Step 3: Scrambling-code identification.

During the third and last step of the cell search procedure, the mobile station determines the exact primary scrambling code used by the found cell. The primary scrambling code is typically identified through symbol-by-symbol correlation over the CPICH with all codes within thecode group identified in the second step. Afterthe primary scrambling code has been identified; the primary CCPCH can be detected. And the system- and cell specific BCH information can be read.

WCDMA Air interface channel

Briefly describe UMTS air interface channel types and their functions.

There are 3 types of channels across air interface – physical channel, transport channel and logical channel:

·         Physical Channel: carries data between physical layers of UE and NodeB.

·         Transport Channel: carries data between physical layer and MAC layer.

·         Logical Channel: carries data between MAC layer and RRC layer.

1.      Logical Channel:

·         Control channel:   BCCH, PCCH, CCCH, DCCH.

·         Traffic channel:    DTCH, CTCH.

2. Transport Channel:

·         Common control channel:  BCH, FACH, PCH, RACH, CPCH.

·         Dedicated channel: DCH, DSCH.

3.      Physical Channel:

·         Common control channel: P-CCPCH, S-CCPCH, P-SCH, S-SCH, CPICH,        AICH, PICH, PDSCH, PRACH, PCPCH, CD/CA-ICH.

·         Dedicated channel:         DPDCH, DPCCH.

Broadcast Control Channel (BCCH):

 It broadcast system control information for all mobiles in a cell like Code values in the cell, neighbor information, allowed power levels in downlink direction.

Paging Control Channel (PCCH):

   It transfers paging information in downlink direction.  Network page the mobile to discover the UE location or UE in a cell connected state.

Common Control Channel (CCCH):

Network may have certain tasks which are or may be common to UE in the cell. It’s being used in both direction DL & UL. The CCCH is also used when UE is accessing a new cell after cell reselection.

Dedicated Control Channel (DCCH):

When there is dedicated/active connection means RRC connection between the network and the mobile, the control information transferred using DCCH. It’s a bi-directional channel.

Dedicated Traffic Channel (DTCH):

It is used transfer the user data between the network and the UE in both uplink and downlink directions.

Common Traffic Channel (CTCH):

It is used to transfer the data from one point to all mobiles or a specified group of mobiles.

Dedicated Channel (DCH):

 It is the channel used to send dedicated control and user data between UE and the network in both uplink & downlink directions

Random Access Channel (RACH):

It is used to send control information from UE in the uplink direction. Also may carry short user packets.

Forward Access Channel (FACH):

It is a downlink common channel used to send small amounts of control and user data.

Broadcast Channel (BCH):

It broadcast system information in the downlink direction for all mobile stations in a cell.

Paging Channel (PCH):

It’s a downlink common channel used to send paging notification messages.

Dedicated Channel (DCH):

It is a channel that is used to send dedicated control and user data between the UE and the network in both directions

(Paging Indicator Channel) PICH:

 It is used to carry paging and notification message to all UEs and it is always associated with SCCPCH

 (Acquisition Indicator channel) AICH:

It is used in random access procedure by network to indicate that the RACH preamble was detected

(Synchronization channel) SCH:

It is downlink channel. It is used to cell search procedure and synchronization with network. There is two type of SCH primary & secondary

 (Physical Random access channel) PRACH:

It is uplink channel and Initial message when UE want gain access to network and transfer small amount of data

(common Pilot channel) CPICH:

It is downlink channel and used to continuously sending scrambling code to cell. It is also aids channel estimation for cell re-selection and Handover for UEs. There are two types of CPICH- Primary and secondary.

 (Primary-common control physical channel) P-CCPCH:

It is downlink channel and used to carry Synchronization channel (SCH) and BCH. It has fixed rate of 30 Kbps.

 (Secondary- common control physical channel) S-CCPCH:

It is downlink channel and used to carry PCH and FACH. It has variable bit rate from 30kbps to 1,920 kbps.

Dedicated Channels:

Dedicated Physical Data Channel (DPDCH)

Dedicated Physical Control Channel (DPCCH)

Dedicated Physical Control Channel (DPCCH)

For each radio link, there is one DPCCH, it carries control information like

• Pilot bits (used to support channel estimation at rake receiver)
• Transmit Power Control (TPC) commands (Used power control)
• Feedback information (FBI) needed with transmit diversity
• Transport Format Combination Indicator (TFCI)

Spreading factor is always 256.

Dedicated Physical Data Channel (DPDCH)

 Each radio link may have no DPDCHs or several DPDCHs.

• Spreading factor for the DPDCH can be between 256 and 4.

DPCCH & DPDCH are time – multiplexed in downlink but uplink these are I/Q modulation.

What is Erlang ?

Erlang :   An Erlang is a unit of telecommunications traffic measurement.  Strictly speaking, an Erlang represents the continuous use of one voice path.  In practice, it is used to describe the total traffic volume of one hour.  in other words " a one ckt  can one hour of traffic is known as 1Erlang"

For example, if a group of user made 30 calls in one hour, and each call had an average call duration of 5 minutes, then the number of Erlangs this represents is worked out as follows:

Minutes of traffic in the hour	=	number of calls x duration
Minutes of traffic in the hour	=	30 x 5
Minutes of traffic in the hour	=	150
Hours of traffic in the hour	=	150 / 60
Hours of traffic in the hour	=	2.5
Traffic figure	=	2.5 Erlangs

The main Erlang traffic model are listed below

  Erlang BThis is the most commonly used traffic model, and is used to work out how many lines are required if the traffic figure (in Erlangs) during the busiest hour is known.   The model assumes that all blocked calls are immediately cleared.

  Extended Erlang BThis model is similar to Erlang B, but takes into account that a percentage of calls are immediately represented to the system if they encounter blocking (a busy signal).  The retry percentage can be specified.

  Erlang CThis model assumes that all blocked calls stay in the system until they can be handled.  This model can be applied to the design of call center staffing arrangements where, if calls cannot be immediately answered, they enter a queue.  

LTE Architecture

WCDMA Architecture